Monday, December 27, 2010

The First Disaster

More and more boat parts emerged from plywood as my saw once again sliced through the thin sheets of okoume today.  Joining the growing pile of parts were the cabin deck halves, cockpit deck halves, cockpit sides, and many more parts.  Most of the cuts were made with my trusty circular saw.  For parts that are the same port and starboard, I'd stack two pieces of plywood and cut both parts at the same time. 

Cabin deck halves (both halves cut at the same time)

I also cut out the centerboard halves.  The centerboard will consist of two pieces of 3/8" plywood glued together to form a nice 3/4" thick centerboard. 

Centerboard halves, clamped together and freshly cut out.
 Since these pieces are identical, I naturally used the magic "stack 'em and cut 'em" trick to make sure they came out identical.  This lead to my first major disaster on PocketShip.  The centerboard halves were laid out pretty tightly on the piece of plywood. Since they were so near other parts, there wasn't much extra material surrounding the rough-cut bits o' plywood containing the centerboard halves.  When I stacked these two pieces of plywood together, I gave myself credit for doing a better job of aligning them than I had actually done.  The result was that a roughly 1"x6" piece of one half of the centerboard is missing. 

Disaster strikes!  One half of the centerboard is missing a little something.

One thing that I've learned in boatbuilding is that disaster WILL strike.  Something will get incorrectly cut, glued, sanded, not sanded, dropped, mixed (think epoxy), or delaminated.  And then you have to figure out how to undo, fix, or obfuscate your mistake.  And yes, it is always YOUR mistake.  Always.  The key is to not kick yourself too much or get down about it.  Keep a level head and think it through.  Having a sanguine Norwegian temperament helps.  There's always a way out.  Maybe a time intensive or expensive way out, but a way out nonetheless. 

Nine times out of ten, salvation comes in the form of the wood butcher's friend, epoxy.  This isn't one of those times, though I suppose one solution would be to whip up a big batch of thickened epoxy and glob it into where there should have been plywood.  But I'm not going to do that.  The possible solutions I've come up with so far are:

1.  Buy another sheet of 3/8" plywood and try again.  Disadvantage:  Cost.

2.  Cut a small bock of plywood roughly the shape of the whats missing and bond it it when the centerboard halves are glued together.  Disadvantage:  It'll take frustrating fiddling to get the piece to fit just right.

3.  The transom is cut out of 3/4" teak plywood.  The transom requires about 1/2 a sheet of plywood, leaving a fair bit of 3/4" plywood left over.  I am going to cut a couple of other parts (rudder cheeks and tabernacle) out of the remainder, but that'll still leave enough 3/4" to cut out a solid centerboard.  Forget about gluing two halves together!  Disadvantage #1:  The centerboard has a square cut out of it into which lead will be poured so that the board will actually go down into the water when it is lowered.  There is a rabbet in the center of the board cut around the perimeter of this hole so that the lead has something to hang on to.  Cutting this rabbet is really easy when you have to halves waiting to be joined.  Not so much fun when you have to excavate it from the 3/4 monolith.  But doable.  Disadvantage #2:  Cost.  That teak plywood is expensive.  In terms of cost per unit area, I could get that whole sheet of 3/8" plywood of the cost of a centerboard-sized piece of 3/4" teak.  On the other hand, I've already bought the 3/4" plywood, and I don't currently have any other plans for the wood that could make up my new centerboard.  So...

I'm undecided about which way to go.  I'll give it some thought, and in the meantime keep working on cutting out parts!

Friday, December 3, 2010

Jigsaws? Where we're goin', we don't need jigsaws.

My progress in laying out the final two dozen or so parts on the plywood has slowed considerably of late, largely due to Thanksgiving and other "hectic schedule." I did manage to take the pieces of plywood I've marked up so far out to the shop and cut out a bunch of parts. My newest ally in the sawdust wars was my circular saw.

I first tackled the cockpit/coaming side decks.  The manual says that a circular saw is good at cutting long gentle curves, so these parts seemed like good candidates.  So, I put a new carbide tipped blade on my saw and got to it.  Wow!  The cuts were remarkably accurate, fair and clean.  I cut the two partss separately instead of stacking two pieces of plywood and cutting them out at the same time.  After cutting them out, I put the two pieces back-to-back, et viola, as identical as can be.

Cutting out one of the cockpit side decks.

That worked so well at I decided to apply my circ' saw to the companionway and hood tops.  Those came out well too, and soon I was using that saw for any line on a part that was straight enough for the saw to handle.  I'd only switch to the jigsaw when quarters or corners got too tight.

Though I cut the rails separately I did stack a few other soon-to-be-identical parts before cutting, including the rudder sides and fore and aft keel sides.

Rudder halves, still clamped together after being cut out.  yes, I even used my circular saw on the straight bits of this.

 I spent maybe a total of two hours cutting out a bunch of parts.  I am looking forward to doing more, but thanks to work commitments, I probably won't able to get anything done for the next two-ish weeks.  Then it'll be close to Christmas, so realistically, it may be the New Year before much more gets done.

The parts are starting to pile up.